Page 1 of 2
setting up the transport control from d8b to cubase
Posted:
Sun Aug 21, 2011 7:53 pmby sweck
how does one go about the config of this?
ive connected a lead to the back of the mackie cpu which has a midi in and midi out, ive hooked these up to my soundcard, had a look in cubase 5 in device set up and config'd the mackie hui and set the relevant inputs. Is this the right way or is it something else. much appreciated and sorry to bother
Re: setting up the transport control from d8b to cubase
Posted:
Mon Aug 22, 2011 5:21 amby FrankH
This should do the trick. The D8B sends MMC commands (Play, Stop, FF, REW) to Cubase, sees them and responds by sending MMC back to the D8B.
There's hardly anything required to set up in the D8B itself. Open the MIDI Setup menu and set the three MIDI Device ID dropdowns to: Device ID 0
Note that I have "MIDI Clock Follows Project Position" unchecked. I work with looped sections a lot, and many times I don't want the D8B to keep looping the timecode. Check this choice and the D8B will loop the timecode between the L&R markers.
Re: setting up the transport control from d8b to cubase
Posted:
Mon Aug 22, 2011 5:53 amby High C Double G
What Frank said... he is one smart cookie alright! AND he has a very cool avatar!
Re: setting up the transport control from d8b to cubase
Posted:
Mon Aug 22, 2011 7:59 pmby sweck
thanks a mil Frank, I tried this but still not getting it running for some reason, when i bought the d8b i was given 2 sets of leads that seem to connect to the same place on the cpu, the first one ive tried so far basically plugs into the cpu and has 2 midi connectors on it. the other lead i havent tried yet has midi + a few others hanging out of it. Il give this lead a go.
Re: setting up the transport control from d8b to cubase
Posted:
Mon Aug 22, 2011 9:52 pmby FrankH
Perhaps if you posted a photo or two of what you have, it'll save a round of "20 questions". This is what mine (dust and all) looks like:
Re: setting up the transport control from d8b to cubase
Posted:
Tue Aug 23, 2011 6:50 pmby Petersueco
I have to say that mine MIDI breakout cable do not look like the one in the picture.
Sweck, the cable that has MIDI and a few others cables hanging out is not for the d8b, AFAIK.
Peter Holmquist.
Re: setting up the transport control from d8b to cubase
Posted:
Tue Aug 23, 2011 11:04 pmby FrankH
I have to say that mine MIDI breakout cable do not look like the one in the picture.
Let me guess....no dust on yours?
Seriously....the unit in the pic was the standard issue MIDI breakout connector we shipped with D8Bs and HDR24s for at least the first two years or so. What does yours look like?
Re: setting up the transport control from d8b to cubase
Posted:
Tue Aug 23, 2011 11:11 pmby anyhorizon
I wish I had one or two of those. So much neater than the floppy cable.
Peter
Re: setting up the transport control from d8b to cubase
Posted:
Wed Aug 24, 2011 4:02 amby Petersueco
FrankH wrote:I have to say that mine MIDI breakout cable do not look like the one in the picture.
Let me guess....no dust on yours?
Seriously....the unit in the pic was the standard issue MIDI breakout connector we shipped with D8Bs and HDR24s for at least the first two years or so. What does yours look like?
Now I'm not sure, but i guess I have a black breakout cable, like the
floppy one Peter is saying.
That one looks really neat BTW.
Re: setting up the transport control from d8b to cubase
Posted:
Wed Aug 24, 2011 7:09 amby FrankH
That one looks really neat BTW.
If memory serves me correctly, the model I have was replaced by the "floppy" version for two reasons: it was pricey and the manufacturer could not supply the quantities the shipping schedule required. So someone was tasked to look for a second source and found the "floppy" version.
And it goes without saying, when it came down to the D8B's BOM, cheaper always won.