Change font size   Print view

D8b clocking question!!!

Discussion board for Mackie's d8b Digital Console users.

D8b clocking question!!!

Postby McKay Records » Tue Jul 03, 2012 6:38 pm

Ok I have a m-audio profire lightbridge 34in/36out connected to the d8b via optical, I currently have a stock clock card "yeah I'll get an apogee soon" but for now is there a way to sync the two devices thru midi or spif using the d8b word clock as the master???
McKay Records
Registered user
 
Posts: 7
Joined: Wed Apr 18, 2012 2:14 am
Location: GA

Re: D8b clocking question!!!

Postby Crash » Tue Jul 03, 2012 6:55 pm

Can I sync other devices to the D8B via ADAT (ODI - light pipe) or AES EBU without the Sync card?
Yes. ADAT/ODI and AES/EBU carry clock info with the digital signal. The D8B must be in Internal mode. You can even chain devices using ADAT ODI or AES EBU

I took this from the Mackie website. Does that answer it? The unknown is the lightbridge.
User avatar
Crash
Premium Member
Premium Member
 
Posts: 1286
Joined: Fri Nov 21, 2008 10:05 pm

Re: D8b clocking question!!!

Postby OscarPro1 » Fri Oct 12, 2012 7:45 pm

McKay Records wrote:Ok I have a m-audio profire lightbridge 34in/36out connected to the d8b via optical, I currently have a stock clock card "yeah I'll get an apogee soon" but for now is there a way to sync the two devices thru midi or spif using the d8b word clock as the master???


For those who may be having the above issue...I solved it by using the Lightbride as a slave on ADAT optical 1 and connecting the midi cables in/out accordingly thru the breakout cable to the d8b CPU. (Make sure your sample rate is matched correctly on the d8b and Lightbridge). Then configure HUI to be on in your d8b GUI page and set your DAW software to receive the HUI mode. These setting will vary depending on your DAW platform. In my case i have successfully set Pro Tolls and Logic to work smoothly.

A
Knowledge is the beginning of Wisdom... Let the learning begin.
User avatar
OscarPro1
Premium Member
Premium Member
 
Posts: 66
Joined: Mon Jul 23, 2012 12:41 pm
Location: London

Re: D8b clocking question!!!

Postby FrankH » Fri Oct 12, 2012 11:47 pm

is there a way to sync the two devices thru midi or spif using the d8b word clock as the master???

Specifically to your question as written: what the two guys above said....with exception to this part:
Then configure HUI to be on in your d8b GUI page and set your DAW software to receive the HUI mode. These setting will vary depending on your DAW platform. In my case i have successfully set Pro Tolls and Logic to work smoothly.
Ignore this unless you need to work in HUI mode.

A little more info on what kind of DAW and platform you use could help with some targeted user inspired details.
User avatar
FrankH
Premium Member
Premium Member
 
Posts: 375
Joined: Wed Nov 26, 2008 7:21 pm

Re: D8b clocking question!!!

Postby OscarPro1 » Sat Oct 13, 2012 10:20 am

Yes... Thanks for the clarity...
Sorry guys...
I added the bit about the HUI should the syncing of transport functions with your DAW be needed in addition to midi. That section should be ignored if HUI is not intended in your syncing scenario.

A... :)
Knowledge is the beginning of Wisdom... Let the learning begin.
User avatar
OscarPro1
Premium Member
Premium Member
 
Posts: 66
Joined: Mon Jul 23, 2012 12:41 pm
Location: London

Re: D8b clocking question!!!

Postby Bruce Graham » Sat Oct 13, 2012 1:53 pm

Could a "bad" clock card stop the HDR from Recording?

All sampl rtes have been triple checked.

BG in Canada
Bruce Graham
Premium Member
Premium Member
 
Posts: 717
Joined: Tue Mar 15, 2011 12:02 am
Location: Walkerton, Ontario, Canada

Re: D8b clocking question!!!

Postby Casey_Pittman » Sat Oct 13, 2012 4:32 pm

A bad clock card would not let the d8b boot up properly if at all.

-Casey
d8b V3 into RME HDSP 9652 with Cubase 7.5
User avatar
Casey_Pittman
Premium Member
Premium Member
 
Posts: 342
Joined: Mon Aug 31, 2009 10:51 pm
Location: Texas

Re: D8b clocking question!!!

Postby Crash » Sat Oct 13, 2012 9:22 pm

Casey_Pittman wrote:A bad clock card would not let the d8b boot up properly if at all.

-Casey


A d8b should be able to boot up, even of there were no card in the slot but it won't pass audio.
User avatar
Crash
Premium Member
Premium Member
 
Posts: 1286
Joined: Fri Nov 21, 2008 10:05 pm

Re: D8b clocking question!!!

Postby Bruce Graham » Sun Oct 14, 2012 1:31 am

Let me re-phrase (or is it re-phase), as my question wasn't correct.

I am using an Apogee Word Clock Card in my D8B which is acting as the Master for my Mackie HDR. The HDR will not record even though all Sample Rates appear to be set correctly on both the D8B & HDR.

The D8B is doinf what it should do. Big "Record Light" turns solid when engauged, and the little record LED on the channel also turns solid.

The HDR Channel Record LED flashes on the correct track but doesn't go into reocrd, and, the transport controls on the HDR do not light up either. Doesn't matter if the D8B is connected or not. (more info, better answers, I hope).

There is another "Weird" issue which is a "ticking" noise along with the audio on many of the tracks BUT not all.

I have only recently purchased the HDR so the audio I am listen to came with the machine. It is not anything I have recorded as ..... I can't record.

Any help would be great. Thanks.
BG
Bruce Graham
Premium Member
Premium Member
 
Posts: 717
Joined: Tue Mar 15, 2011 12:02 am
Location: Walkerton, Ontario, Canada

Re: D8b clocking question!!!

Postby Crash » Sun Oct 14, 2012 2:26 am

Sounds like you don't have your clocking sorted out. Have you checked the setup page of the hdr?
User avatar
Crash
Premium Member
Premium Member
 
Posts: 1286
Joined: Fri Nov 21, 2008 10:05 pm

Next

Return to d8b Forum

Who is online

Users browsing this forum: Google [Bot] and 56 guests

cron