probox Firmware (UPDATE V2.02.05)

[munkustrap]

Hi probox users

in a few days a Firmware update will be released. YES ist with HUI !!!

Version will be 2.01.0x

I will email you all a link where you can download the whole stuff that you Need to update your prox.
The update itself will take 5 seconds. Preparing everything is about 5 minutes (including reading the update Manual)

changes:
- HUI implemented
- Nearfield/Main Speaker swap fixed
- Fader/off Button (no fader send/receive commands)
- Meterbridge off button (maybe helpfull if try to use the Audio)
- Fader Filter Implemented (due to bad Hardware design of the d8b the faders will slightly move +/- 1 value. For me that doesn't matter but If you want to get rid of that you can use the faderfilter. But the fader will react less smooth the higher you use the faderfilter)
- Baudrate is selectable (normal or boost) This is if you want to use an unhacked probox d8b Firmware that will also communicate with the d8b CPU
- Emulation Modes for Logic/mackie (1MCU2XT_1, 1MCU2XT_2,3XT) if you want to use two d8b with two proboxes
- now the nearfield/main Speakers can be muted by pressing the selected Speaker button again (button led will flash then)
- Logic Meterbridge fix (the OL was at -0,6dB) now its corrected.
- longer heartbeat timeout set, as two users had the "cool" las vegas effect. This is fixed.

[mixingmusic]

Hi Ralph,
Is the ProBox Firmware Update finished or are you still working on it ?


MIXINGMUSIC

[munkustrap]

Hi Ralph,
Is the ProBox Firmware Update finished or are you still working on it ?

When you said a few days I thought that meant a few days...

It's been a Month...

I'm not trying to be a Jerk.....It just seems like you are busy with other things these days instead of your ProBox...

Best Regards

MIXINGMUSIC

Hi Mixingmusic and all others

for sure the development is not dead.
So there are some simple reasons for the delay.

My protools 30days Trial run out before I could finish the Firmware. I got a solution yesterday, but I've to try it out. Additional I was busy in the Studio and I have to do a Business trip this week, so in that case no Progress the next week.

BUT:
on the new beta Firmware the whole Logic/Mackie Stuff is working so the beta can be used for all DAWs execpt Protools.
On HUI there are Problems with the MTC Display and the refresh of the Display when changing between Projects.
Version: 2-01-04

Downloads: http://www.weritz.com/probox/downloads/
username: probox
Password will be mailed to you if you need it.
mail to probox@weritz.com to get your Password


best regards
Ralph

[munkustrap]

Hi, I had a typo mistake on my email address above. Now its corrected.

best regards
Ralph

[munkustrap]

new Firmware available

V2.01.09

all users that work with a beta Version, please update to the latest Firmware

HUI implemented with small changes (needs to be documented)
MCU fader control bug fixed

Downloads: http://www.weritz.com/probox/downloads/
username: probox
Password will be mailed to you if you need it.
mail to probox@weritz.com to get your Password

[ismains]

hi Ralph!

a simple question but i want to do it right
what is the procedure for updating the probox....do i just connect the usb to my pc and copy and paste
the update files or i need to open the probox and use the other cable that you have put in the box

thanks for the info

best regards
Alain

[munkustrap]

Hi

In the Download area there is a document his to Update the firmware.
It is done with the same USB port.
If you have questions send me an Email. There is the chance
Much bigger that i react faster.

Best regards

[mixingmusic]

Best Regards

[ismains]

hi mixing music
here is step by step as i have did it
-go to the update link with the password that munk as gave you
-select flashtool and download ''update _via_MIDI.zip (unzip the archive, select linux mac or windows)
run the flashprogram
-open the pdf firmware_update_manual_v1-0.pdf(always on flashtools page)
-once the pdf as open scroll to 1.1 follow the instructions step by step
you should be able to achieve your update like that , it as work fine for me
don't forget to also download the firmware update Under firmware this download will be needed to load
the HEX into the flashtool.
hope that help you

best regards
Alain

[munkustrap]

Hi

There is a manual Online, how to Update.
If anybody has problems please e-mail me, so can react Faster.
Even i would like to know the problems that you have
Because of bad documentation. I will Update the document then to make it more clear.

Best regards
Munk