Change font size   Print view

New D8B user.

Discussion board for Mackie's d8b Digital Console users.

New D8B user.

Postby scottosterloh » Sun Mar 03, 2019 6:58 pm

I really dig how much info. is on this forum. I recently got a D8B I'm coming from a hybrid analog/digital set up. My last mixer started to hv too many issues so after a lot of research I made the switch. I'm going to have questions for sure, but for now just a few. I bought the d8b with a issue. So here are my first 4 questions.
1.How to fix DSP control card not ready error message.
2.I use a lot of outboard gear, are the aux sends send and return?
3. How much is a Probox?
4. How would I use an outboard piece on my master channel?
Thanks

Mackie D8B
Motu 24io
Moth 2408
Studio One
scottosterloh
Registered user
 
Posts: 48
Joined: Sun Feb 24, 2019 1:21 am

Re: New D8B user.

Postby adamstarr » Mon Mar 04, 2019 6:56 am

I just bought a D8B last week and I had the DSP control card issue as well as system error 43.

Since the unit didn't come with the parallel 25 pin cable I was unaware that it needed to be connected in order to boot, it does.

Found and old cable, hooked it up to the PSU and it passed the DSP issue without problems.

I also reset CMOS on the motherboard and replaced the CMOS battery to clear system error 43.

$25 in parts and 1 hour in labor and the board works perfectly.

Good luck fellow newbie :)
adamstarr
Registered user
 
Posts: 3
Joined: Thu Feb 28, 2019 12:53 am

Re: New D8B user.

Postby scottosterloh » Tue Mar 05, 2019 5:02 am

Thanks I will definitely try that. I'll let U know. How are you liking your D8B? What kind of interface and DAW are U using if any. Thanks
scottosterloh
Registered user
 
Posts: 48
Joined: Sun Feb 24, 2019 1:21 am

Re: New D8B user.

Postby scottosterloh » Wed Mar 06, 2019 6:57 am

I moved the 25 pin cord around and I got communication between the software and the mixer except I have a blank screen on the mixer when I adjust eq/comp/ gate. Maybe try to replace the 25 pin cord completely.
scottosterloh
Registered user
 
Posts: 48
Joined: Sun Feb 24, 2019 1:21 am

Re: New D8B user.

Postby arjepsen » Wed Mar 06, 2019 8:11 am

Check your bios settings, and also give it that new battery.
That might fix it
arjepsen
Premium Member
Premium Member
 
Posts: 603
Joined: Sun Nov 02, 2014 9:10 pm

Re: New D8B user.

Postby scottosterloh » Wed Mar 06, 2019 2:31 pm

What should I be looking for in the Bios settings? Thanks
scottosterloh
Registered user
 
Posts: 48
Joined: Sun Feb 24, 2019 1:21 am

Re: New D8B user.

Postby Crash » Wed Mar 06, 2019 4:53 pm

scottosterloh wrote:What should I be looking for in the Bios settings? Thanks


Look up in the database for those BIOS settings. Don't go with "Default" as that won't fly. The database is way full of helpful info.
User avatar
Crash
Premium Member
Premium Member
 
Posts: 1286
Joined: Fri Nov 21, 2008 10:05 pm

Re: New D8B user.

Postby Crash » Wed Mar 06, 2019 5:03 pm

As for number 2 on your list, I use a boatload of outboard as well. The auxes will feed the internal F/X via the MFX/UFX cards, depending on what you have, and the 1/4 jacks at the same time. I bring the returns of my whiz bang boxes back on the Mic/line bank of faders.

I feed my dynamics boxes via the bus outs and return those via the ALT I/O slot equipped with an AIO.8 card.

As for doing master bus stuff (#4), I mix digital out of the console into an Apogee converter to go analog, hit an A-designs Nail, Pultec, Clariphonic, back to digital into a L2, into my master 2 track deck and return to digital 1 on the console. This allows me to hear pre and post 2 bus processing with the a button hit. Hopefully that makes sense.
User avatar
Crash
Premium Member
Premium Member
 
Posts: 1286
Joined: Fri Nov 21, 2008 10:05 pm

Re: New D8B user.

Postby scottosterloh » Wed Mar 06, 2019 8:12 pm

Thanks that was helpful my friend.
scottosterloh
Registered user
 
Posts: 48
Joined: Sun Feb 24, 2019 1:21 am

Re: New D8B user.

Postby scottosterloh » Fri Mar 08, 2019 2:58 pm

The card error was solved by moving the 25 pin cord around. I repeated the process so for sure that solves the error. I don't hv the fat channel display on the D8B. I'm going to replace the 25 pin cord completely to see if that solves the VFD display issue. If not I will replace the battery. The BIOS settings are normal.
scottosterloh
Registered user
 
Posts: 48
Joined: Sun Feb 24, 2019 1:21 am

Next

Return to d8b Forum

Who is online

Users browsing this forum: No registered users and 4 guests

cron